How to Build a Master Bathroom Vanity

Home » China Newstar News For Bkexport.com

(6/7/2016)

Steps:


1. Cut your 3/4" maple plywood down to size for the framing. Ours was 80-9/16"x21 1/8", but the size will vary depending on your bathroom dimensions.

2. Drill about seven holes in four columns along the shorter length, starting 3 feet, 8 inches in from the edge. The two columns of holes toward the center should be 32 inches from their respective sides.

3. Secure a piece of maple plywood between the two center columns to give extra depth where the drawers will be.

4. The two sides of the vanity are made with 3/4" walnut plywood. Ours were 20-7' 8" high by 21-1/8" wide. Attach them to the outer edges.

5. Our center uprights will be the same dimensions as the sides, but two will be made from 3/4" walnut and two will be made from 1/4" maple.

6. Create notches in the center dividers with a router so they'll be able to fit securely over a ledger that will later be installed. The notches should be 4 inches high by 3/4" wide and will face the wall when installed.

7. Attach the larger walnut dividers in the center with the notches facing toward the back. Nail the thinner maple dividers to the outside of the larger dividers to provide more depth and to accommodate the size of the drawers.

8. Create pocket holes along the edges of four strips of 3/4" finished walnut. This will be the trim across the front that hides the plywood grain. Ours measured 80-1/2" x 3-1/8" for the top and 80-1/2" x 1-1/2" for the bottom. The two vertical trim pieces measured 17" x 1".

9. Assemble the walnut pieces together with pocket screws. Slide the trim on to the front of the cabinet and secure it with nails.

10. Now it's time to assemble the drawers. We're using pre-finished drawer sides with a pre-cut dado. Cut the sides down to the appropriate size to fit inside the cabinet. For the bottom, cut down 1/4" maple and slide it through the dado cut. Attach the front piece to complete the drawer.

11. Attach a strip of plywood 4"x80-1/2" to your bathroom wall to serve as a ledger. It should be rounded over on one long edge. Be sure it lines up with the notches on the center dividers.

12. Set the cabinet in place in your bathroom and secure it with screws. The center dividers will attach to the ledger at the notches.

13. Now cut down 3/4" walnut plywood for the drawer facing and doors. Our doors measured 16-3/4"x15-3/8" and our drawer fronts measured 5-7/16"x15-3/8".

14. Seal the walnut with an acrylic finish for a better look and to protect it from the humidity in the bathroom.

15. Attach glides and slides on the drawers and inside the cabinet. Attach hinges for the doors.

16. Attach the doors with the hinges and the drawer faces will be secured from the inside of the drawer with screws. Be sure there is a continuous grain across the front of the vanity since it was all cut from the same piece of wood. This will give a nice, flowing look.

17. Attach door and drawer hardware.


Home | Products | Why Newstar | Replica Rolex | News | Contact us | Industry News | FAQ's

Copyright (c)2017 All Rights Reserved NEWSTAR( QUANZHOU) BATH & KITCHEN CO.,LTD
Tel: +86 - 595 - 2219 8926 , 2228 9926 * Fax: +86 - 595 - 2216 6926
* E-mail: sales@newstarchina.com , sales@bkexport.com


This is my to start with prime three Rolex Day-Date bogus watches evaluate report and that i desire to carry towards your awareness the most beneficial 3 Rolex reproduction Day-Dates that i reviewed on my blog site. I haven?ˉt reviewed a good deal of reproduction Rolex Day-Date watches largely on account of my preference for additional hip and new watches. I do recognize their typical and stylish electrical power and appears nevertheless, and every time I see an original or a excellent pretend Replica Watches on the market I like them. They?ˉre these types of a straightforward and simple watch to get that don?ˉt scream out lots of attention nonetheless they do the trick plus they increase class into the kinds who don them. Quantity 3 on today?ˉs list is this fully plated yellow gold, gold dial, imitation stone markers Rolex Day-Date replica check out. It appears to be seriously great and legit. The sole motive why I put it at number three is the fact that it?ˉs somewhat over the mild side. Might have preferred Rolex Replica watches it a tad more hefty and it might have felt 100% genuine but however this bit of information is replica best watches mostly accessible to the owner. It?ˉs looks truly excellent even though from all angles and has many of the ideal Rolex factors set up. Two-tone brushed and polished bracelet do the trick too. Have a look at the total Rolex Day-Date picture critique from the link. Number 2 is this two-tone yellow gold plated and stainless steel spherical bezel pretend Rolex Day-Date duplicate check out. Dial seems truly excellent as you can see and all of the Rolex markings are set up. Women's replica watches Rolex symbol at twelve o?ˉclock appears seriously great way too from this angle and that i like how the roman numerals appear out also. It?ˉs a slightly larger case sizing in comparison to the past reproduction Rolex and it seems much more up to date. It?ˉs however a basic piece it does not matter what. Seconds hand contains a good sweep and yet again the two-tone brushed and polished bracelet is killing it. Here?ˉs the total picture evaluate on this Rolex Day-Date phony watch. At quantity 1 I chose this all stainless steel Rolex bogus Day-Date look at. As simple as they get but once more as elegant and traditional because they get. They?ˉre some of the most easier watches to go for originals and you will Knock Off Breitling evidently see from this one that it?ˉs a no-brainer. All the things is in place and also the looks are there. Roman numerals are chrome steel, white dial is as simple as can be as well as the working day and day window are crystal crystal clear. Fluted bezel provides it far more of that previous, vintage, and traditional look as well as the two-tone Replica Rolex brushed and polished presidential bracelet does the trick as well. Look into listed here the complete photograph overview on this bogus Rolex Day-Date look at.